Automatic Drum Production Line

The automatic big round can making production line adopts the modular design and integrates tapering、flanging、beading、bottom lid sealing、reversing、seam automatic detection、top lid sealing to be a whole.This line is suitable for 10L-25L big round can automatic making.

What is a neck-in drum?

It is made of three pieces of metal (mostly tinplate) : the body, the bottom and the lid of the cans. The cans is conical or cylindrical shape. The body of the cans has two ribs. The scope of closed barrel: capacity 20-25l, diameter 200-300mm, height 150-480mm.

Working process of full-automatic neck-in drum production line

First place cutting cans body material in the resistance welding machine automatically picking place, Suck by the vacuum sucker to the feeding roller, through the feed roller to the deflection roller bending processing, then roll into the forming device into cylindrical body, body is fed into the resistance welding machine, after the accurate positioning for resistance welding. After welding, the cans body is automatically fed into the frame of the coating machine. There are two schemes of spraying type and rolling coating type, which are available for users to choose. It is mainly used to prevent the welding seam line from contacting air and causing rust. The cans body is transferred to the neck-in drum combination machine, and the cans body is in an upright state through the vertical device, and the screw rod reciprocates. The first operation is the cans body expansion. When the cans is in position, the cans tray is controlled by a servo motor and the tank is sent to the expansion cone mold. Step 2 turn up and down. If the bottom cover is required to make 7 layers, the third step can be carried out and the flanging amount can be further increased at the bottom. The upper die is fixed on the body, and the lower die is installed on the CAM to complete the upper and lower flanging when the CAM is jacked up. The fourth step is beading. After completing the above four steps, the conveyor belt will send the cans to the cover of the sealing machine. Conveying to the turn over device to change the direction of the lower part of the cans body, and then carry out the automatic induction of the Lid feeder and sealing process.

Equipment composition of full-automatic neck-in drum production line

Full automatic welding machine

Full automatic coating machine
Major parameters
Linear rate of welding 6-21m/min
Production capability 15~38Cans/min
Applicable can diameter Φ220~Φ300mm
Applicable can height 250~450mm
Applicable material Tinplate steel-based
Applicable material thickness 0.25~0.42mm
Seam welding landing 0.8mm 1.0mm 1.2mm
Seam point distance 0.5-0.8mm
Applicable copper wire diameter 1.5mm 1.7mm
Cooling water Temperature 12~18°CPressure:0.4-0.5Mpa Discharge 12L/min
Compressed air consumption 400 L/min
Pressure of compressed air 0.5Mpa-0.7Mpa
Power 380V±5% 50HZ
Total power 63KVA
Packed Dimension 2300x1800x2000mm
Packed Weight 2500Kg

Full automatic coating machine

Full automatic coating machine
Major parameters
Applicable tank diameter Φ52mm*Φ350mm
Applicable tank height 60-600mm
coating speed 10-45m/min
External repainting width 10-16m/min
Compressed air 0.4MPA/CM2
equipment power 50/60Hz P=400W
voltage UVW 380V 50/60HZ
Dimensions(L*W*H) 1800*600*1300mm
Total Weight 500kg

Electromagnetic drying machine

Electromagnetic drying machine
Major technical parameters
Model GDCHG-286-8
Coneveyor speed 5-30m/min
Coneveyor type Flat chain drive
Can hight range 200-400mm
Heating type Induction
Effective heating 800mm*8(30cpm)
Highter heating 1KW*8(temperature set)
Frequency setting 80KHz±10KHz
Electro.Radiation Protective Covered with safety guard
Sensing distance 5-20mm
Induction point 40mm
Induction time 25sec(410mm H,40cpm)
Rise time Distance 5mm 8 sec&280℃
Cooling induct.coil No require water/air
Voltage & Frequency 380V +N ﹥10KVA
Machine dimension 7500*700*1420mm
Gross weight 700KG

Full automatic can body combination machine

Full automatic can body combination machine
Major parameters
Production capacity (cans/min) 25-30
Diameter (mm) 200-300
Can height (mm) 230-460
Thickness of tinplate (mm) ≤0.5
Air pressure (mpa) 0.5
Power (kw)
Front combination machine (kw) 33
2 sets of can seamer (kw) 15.1
Conveyor (kw) 2.15
Size (mm) 15000×1650×2880
Front combination machine (T) 7
2 sets of can seamer (T) 7
Convyor (T) 1

GT4B30 Automatic can sealing machine

1-5L Automatic can sealing machine
Major technical parameters
Production capacity (cans/min) 25-30
Diameters(mm) 200-300
Height (mm) 230-460
Thickness of tinplate(mm) ≤0.4
Air pressure (mpa) 0.3-0.5
Motor type(kw) Y132S-4 5.5
Front conveyor frame (mm) 3000
Size (mm) 2200×1200×2800
Weight (T) 5

The layout of the production line

The layout of the production line

Tin can making artcraft

Tin can making artcraft

The following products are produced by this equipment

Full AutoCan 1-5L Rectangular Can Production Line Application (1)
Full AutoCan 1-5L Rectangular Can Production Line Application (2)
Full AutoCan 1-5L Rectangular Can Production Line Application (3)
Full AutoCan 1-5L Rectangular Can Production Line Application (4)
Full AutoCan 1-5L Rectangular Can Production Line Application (5)